 |
 |
 |
Hex-Head - Fully Threaded Aluminum
 |
| Part No. |
EDP No. |
L | L1 | D | Thread (G) |
| 441203-AL | 59341 | 1.75 | 1.50 | 1/2 | 5/16-18 |
| 491203-AL | 59342 | 1.50 | 1.25 | 9/16 | 3/8-16 |
| 485203-AL | 59344 | 2.75 | 2.50 | 9/16 | 3/8-16 |
| 486203-AL | 59345 | 4.00 | 3.75 | 9/16 | 3/8-16 |
Hex-Head - Fully Threaded Carbon Steel
|
| Part No. |
EDP No. |
L | L1 | D | Thread (G) |
| 105203 | 59301 | 0.84 | 0.75 | 1/4 | 8-32 Nylon |
| 305203 | 59313 | 1.09 | 1.00 | 5/16 | 10-32 |
| 202203 | 59303 | 3.13 | 3.00 | 7/16 | 1/4-20 |
| 205203 | 59302 | 1.88 | 1.69 | 7/16 | 1/4-20 |
| 461203 | 59314 | 1.00 | 0.81 | 1/2 | 5/16-18 |
| 441203 | 59312 | 1.94 | 1.75 | 1/2 | 5/16-18 |
| 207203 | 59304 | 2.75 | 2.50 | 1/2 | 5/16-18 |
| 491203 | 59315 | 1.50 | 1.25 | 9/16 | 3/8-16 |
| 210203 | 59305 | 3.00 | 2.75 | 9/16 | 3/8-16 |
| 240203 | 59307 | 4.25 | 4.00 | 9/16 | 3/8-16 |
| 527203 | 59316 | 5.25 | 5.00 | 9/16 | 3/8-16 |
| 325203 | 59317 | 2.75 | 2.50 | 3/4 | 1/2-13 |
| 220203 | 59306 | 3.31 | 3.00 | 3/4 | 1/2-13 |
| 250203 | 59308 | 4.38 | 4.00 | 15/16 | 5/8-11 |
Pressure-Matic Bolt Retainer Assemblies
  |
| Part No. |
EDP No. |
L | Range C |
C1 | F1 | Thread (G) |
Max. Comp |
Max Pres. |
| 902 | 59020 | 3.20 | 1.06-1.56 | 0.63 | 0.25 | 5/16-18 | 0.50" | 72 lbs. |
| 904 | 59040 | 4.25 | 1.38-3.00 | 0.88 | 0.38 | 3/8-16 | 0.25" | 180 lbs. |
| 910 | 59100 | 4.42 | 2.06-2.81 | 1.00 | 0.38 | 5/8-11 | 0.75" | 468 lbs. |
| For
use with solid bar hold-down clamps. The compression spring allows the clamp to compensate for variations in the material thickness. Clamp capacity is only as great as the maximum spring pressure. |
||||||||
Plunger-Matic Assemblies
 |
| Part No. |
EDP No. |
L | L1 | D | S | Thread (G) |
Max. Comp |
Max Pres. |
| 905 | 59050 | 2.50 | 0.75 | 0.88 | 0.19 | 5/16-18 | 0.19" | 135 lbs. |
| 920 | 59200 | 3.63 | 1.13 | 0.88 | 0.38 | 3/8-16 | 0.38" | 308 lbs. |
| 950 | 59500 | 5.25 | 1.56 | 1.44 | 0.50 | 5/8-11 | 0.50" | 770 lbs. |
| For
use with plunger/straight-line action clamps. The compression spring allows the clamp to compensate for variations in material thickness. Clamp Capacity is only as great as the maximum spring pressure. |
||||||||
